Supplies NEEDED
6 one l/i" head pins
2" four x 1 mm sterling silver rectangle wire Two 1' items of sterling silver chain Two pearl beads
Two one.four mm round sterling silver beads Two sterling silver ear wires
Equipment Desired
Ruler
Marker
Jeweler's saw or tin snips Basic safety Eyeglasses Tough, flat area Awl
Hammer /Ίί" drill bit
Handheld rotary Device, flex shaft, or drill push File
Good grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Wire cutters or tin snips
Spherical nose pliers
one.Use the ruler to evaluate and mark two Γ parts of 4 x one mm rectangle sterling silver wire.
two.Using a jeweler's noticed or tin snips, Slash the 4 x one mm rectangle sterling silver wire into two Γ lengths.
3.File Every single end in the one" rectangle wire pieces to get rid of any burs or tough edges; You should use the file to around the finishes from the rectangle wire items if you want. Make use of a high-quality grit sanding pad to go more than the realm in which you have filed to easy the sides and remove any file marks.
4.Utilize the ruler to evaluate and mark '/*’ from Each and every conclusion of the Γ items of rectangle wire and position a mark in the center in the wire. This could be where you drill the holes to slide The top pins as a result of.
5Next, put with your protection glasses! Then place the Γ rectangle wire items onto a tough, flat surface. Location The purpose with the awl on the mark which you designed /(." from each stop with the rectangle wire parts, and use a hammer to firmly strike when on the highest of your awl. This will make a pilot hole for drilling holes in the rectangle wire.
six.Using a drill bit. drill holes into Every single close of the rectangle wire items by using a handheld rotary Software, flex shaft, or drill press (whilst even now putting on your protection glasses!).
7.Make use of the file or high-quality grit sanding pad to reduce any burs or rough edges still left from drilling holes to the rectangle wire parts.
eight.Curve both Γ pieces of rectangle wire into a form employing a ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, use two pairs of chain nose pliers. Holding a single pair in Every single hand, grasp Just about every close of the Γ rectangle wire piece inside the chain nose pliers and gently bend the rectangle wire right into a “C condition, aligning the holes that you choose to drilled on each finish in the Γ rectangle wire items. Assess both equally of your C-shaped rectangle wire pieces and modify the curves so that they are equivalent in dimensions.
Established these apart.
nine.Utilize the ruler to evaluate the chain into Γ pieces. Use the wire cutters to cut the chain, and set these parts apart.
ten.Location a head pin by way of a pearl bead then insert just one one.four mm sterling silver bead.
eleven.Utilize the ruler to measure and mark /t" above the top bead on the head pin. With wire cutters or tin snips, Reduce The top pin wire Yu," previously mentioned the highest bead.
twelve.Utilizing the chain nose pliers, bend The top pin wire close to the highest bead in a ninety-diploma angle.
thirteen.Keep The pinnacle pin Along with the pearl bead as well as silver bead on it in a single hand While using the wire that you bent pointing toward you. Utilizing the spherical nose pliers, grip the top of The pinnacle pin wire that may be pointing towards you and roll it away from you (think of turning the ignition key to start your car). Launch the pliers from The pinnacle pin wire. At this stage, the opening during the loop at the best of The pinnacle pin wire need to be significant more than enough to slide the Γ duration of chain on it in advance of closing the loop of The pinnacle pin. When you insert the chain, make use of the spherical nose pliers to grasp the loop of The top pin wire and roll it closed. You can utilize the round nose or chain nose pliers to adjust the shape of the loop at the top of The pinnacle pin if you might want to.
fourteen.Repeat this action on the 2nd pearl and silver bead. Established these aside.
15.Location a head pin with the hole drilled into one close of your rectangle wire “C* condition with The underside or flat conclude on the inside curve in the rectangle wire *C* shape. Use the ruler to evaluate and mark The pinnacle pin s/u.m earlier mentioned the rectangle wire. With wire cutters or tin snips, Slice The top pin wire previously mentioned the very best from the rings for men rectangle wire.
16.Use the chain nose pliers to bend The pinnacle pin wire beside the rectangle wire in a 90-degree angle.
17.With the chain nose pliers in a single hand, keep the bottom or flat location of the head pin firmly against the rectangle wire with The pinnacle pin wire you bent pointing towards you.
Along with your other hand, use the round nose pliers to grip the top of The top pin wire and roll it from you. Release rings for men the head pin wire. At this stage, the opening from the loop of The top pin wire must nonetheless be large more than enough to slide the tip hyperlink of the one' chain on to iL Now include men's designer rings & wedding bands the chain towards the loop of The pinnacle pin. and afterwards make use of the round nose pliers to grasp men's gold & silver rings the loop of the head pin wire and roll it shut. You need to use the round nose or chain nose pliers to adjust The form on the loop at the very best of the head pin.
eighteen.Repeat this men's rings personalized and engraved process on the other gap from the C-shaped rectangle wire. Instead of introducing the one * length of chain with the pearl as well as sterling silver bead, insert the ear wire at another end. Slip the ear wire on to the loop of The top pin prior to closing the loop.
19.Repeat the previous methods on the second earring.
